Besa-lighting Tara (120V Pendants) Manuel d'utilisateur Page 1
Naviguer en ligne ou télécharger Manuel d'utilisateur pour Éclairage Besa-lighting Tara (120V Pendants). Besa Lighting Tara (120V Pendants) User Manual Manuel d'utilisatio
- Page / 2
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
INSTALLATION GUIDE
Model 1KZ Series -01 (Medium Base Pendant Set 120V)
1KZ.01, Rev.6 12-11
6695 Taylor Rd. Blacklick, OH 43004
www.besalighting.com
CAUTION: Turn off power to electrical box before installing
1. Carefully unpack parts. Remove the Canopy (A) from
the Mounting Plate by unscrewing the Retainer (B). Fully
remove the Retainer from the threaded nipple, then pull
the canopy from the Mounting Plate.
B
2. Prior to mounting fixture to ceiling, cord must be cut to length. Measure the overall length of pendant
drop, then add 25% to allow for shaping of the cord. Cut off excess cord then strip back outer jacket
about 4” in length. To move the Strain Relief (I), simply pinch together and slide down the cord.
3. Install the provided Mounting Screws (C) into the Outlet Box,
leaving 1/4” of threading as shown. Attach the bare copper (or green striped)
fixture ground wire and bare ground conductor from the cord to the supply
ground and secure with Wire Nut Connector (D). Connect the cord
conductors to the supply conductors with Wire Nut Connectors (E)
as shown: Cord conductor with white stripe to white supply wire and
clear cord conductor to black supply wire. Carefully push wires and
wire nuts back into outlet box.
When using the clear style cord, it is advised
that the installer confirm the polarity per
instructions onthe next page.
4. Align the circular openings of the keyhole slots (F)
of the Mounting Plate (G) with the Mounting Screws.
Push the Mounting Plate up over the Outlet Box
until tight to ceiling, then rotate the Mounting Plate
Counter-clockwise and secure with Mounting Screws.
5. To adjust pendant height, push the cable up through
the Cable Grip (H) to desired length. To lower pendant,
push the Cable Grip up, which will release the cable
and allow it to be lowered. Trim the excess cable,
leaving about 6” above the Cable Grip. Position the
Strain Relief close to the Mounting Plate as shown.
C
D
E
FG
Bare or Green Stripe
White Stripe
H
I
Clear
Replacement parts for this 120V Voltage Pendant Set are as follows:
#T1KZ150-SN.01 - 150W 10’ clear cordset and 1 support cables with Nickel Hardware.
For Bronze cordset, use “BR” in place ”SN”. For 15’ cordset, place “L” after metal finish.
1
2
Résumé du contenu
Page 1 - INSTALLATION GUIDE
INSTALLATION GUIDEModel 1KZ Series -01 (Medium Base Pendant Set 120V) 1KZ.01, Rev.6 12-116695 Taylor Rd. Blacklick, OH 43004www.besalighting.com CAU
Page 2 - POLARITY INSTRUCTIONS
INSTALLATION GUIDEAll electrical connections and the installation of this fixture must be in agreement with local codes, ordinances or the NEC (Nation
Produits connexes et manuels pour Éclairage Besa-lighting Tara (120V Pendants)
(6 pages)© 2020, manymanuals.fr. Tous droits réservés | 1.277 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels